|
EC-10 Router
Features
- Designed for heavy production routing
- Heavy duty rotor design for high torque
- Light alloy housing for easy handling
- Tool can be fixture mounted
- Grease fitting for easy bearing lubrication
- Hardened and ground cylinder for optimum
motor performance
- Can be used to route sandwich materials
of varying degrees of
thickness or heavy gauge metals
|
Speed
(RPM)
|
Length
(Inches)
|
Diameter
(Inches)
|
Weight
(Lbs.)
|
Collet Sizes
(Inches)
|
Minimum
Hose Size
|
Air Intake
(FPT)
|
9000
|
9
|
3 7/8
|
9 1/4
|
1/4 3/8 1/2
|
1/2
|
3/8
|
 back
to top
EC-10 Product Illustration
click to enlarge
back
to top
EC-10 Router Parts List
| Index |
Part # |
Previous
Part #
|
Description |
Quantity |
| 1 |
EC 1034 |
|
Trigger |
1 |
| 2 |
EC 4083 |
844083 |
Pin |
1 |
| 3 |
EC 3308 |
|
Hose Adapter |
1 |
| 4 |
EC 3098 |
|
Bushing |
1 |
| 5 |
EC 3097 |
|
Valve |
1 |
| 6 |
EC 2568 |
812568 |
Bolt |
4 |
| 7 |
EC 9046 |
|
Throttle Housing |
1 |
| 8 |
EC 4287 |
864287 |
Pin |
1 |
| 9 |
EC 3303 |
|
Deflector |
1 |
| 10 |
EC 3075 |
833075 |
Pin |
1 |
| 11 |
EC 9040 |
|
Gasket |
1 |
| 12 |
EC 9466 |
|
Ball Bearing |
1 |
| 13 |
EC 9048 |
|
Rear Plate |
1 |
| 14 |
EC 9045 |
|
Motor Housing |
1 |
| 15 |
EC 9147 |
|
Cylinder |
1 |
| 16 |
EC 3195 |
|
Rotor Blade |
4 |
| 17 |
EC 7008 |
|
Adjusting Ring |
1 |
| 18 |
EC 3194 |
|
Rotor |
1 |
| 19 |
EC 3181 |
|
Key |
2 |
| 20 |
EC 9041 |
|
Spindle |
1 |
| 21 |
EC 3075 |
833075 |
Pin |
1 |
| 22 |
EC 9047 |
|
Front Plate |
1 |
| 23 |
EC 2764 |
842764 |
Ball Bearing |
2 |
| 24 |
EC 9044 |
|
Front Housing |
1 |
| 25 |
EC 3012 |
|
Retaining Nut |
1 |
| 26 |
EC 3312 |
|
Grease Fitting |
1 |
| 27 |
EC 3334 |
863334 |
Set Screw |
1 |
| 28 |
EC 3005 |
|
Felt Washer |
1 |
| 29 |
EC 9042 |
|
Collet Body |
1 |
| 30 |
EC 7002 |
|
Collet Nut |
1 |
| 31 |
EC 7003 |
|
1/4 inch Collet |
|
| 31 |
EC 7004 |
|
3/8 inch Collet |
|
| 31 |
EC 7005 |
|
1/2 inch Collet |
|
|
back
to top
EC–10 Router Service & Maintenance
Instructions
Operation:
The tool is designed to operate
on 90 PSI air pressure using a 1/2 inch hose.
Lubrication:
An automatic in-line filter lubricator
is highly recommended to increase tool life as
well as keeping the tool in sustained operation.
If in-line lubricator is not used, the tool should
be lubricated several times daily by disconnecting
the air hose and injecting a few drops of a high
grade No. 10W machine oil in the air inlet.
|
back
to top
Product Safety Warnings
For Your Safety make
sure you apply standard shop
practices at all times when
using this tool. Your failure to apply
these practices may result in serious bodily injury.
Protect your eyes, ears,
and other parts of your body by using safety equipment;
to include Respirator, Safety Goggles, Ear Mufflers
and other necessary safety devices at all times when
operating this tool or when you are in the area where
this tool is being operated.
For maximum stability and safety,
operate this tool only with both hands on the tool.
Follow the cutting tool manufacturer’s mounting
and operating instructions and avoid any direct contact
with the sharp cutting edges of the tool.
Modification or improper use
of this tool, including, but not limited
to, removing guards, mufflers, or other safety devices, voids
all responsibilities of the manufacturer.
Excessive air pressure,
over and above 90 PSI, will increase the RPM,
the sound level, and can be a damaging factor to both
the operator and the tool.
Stay alert! Watch what you are
doing! Do not operates this tool when under the influence
of medication, alcohol, or drugs!
Disconnect the air supply before
changing the cutter and whenever making adjustments
or repairs.
Do not remove warning
tags until both sides have been read and understood
by the person(s) responsible for safety in your plant.
If you need any other information, consult
your supervisor or contact:
E-C Eng. & Mfg., Inc.
P.O. Box 1090
Mountain Home, AR 72654-1090
Phone: (870) 425-3979
Fax: (870) 424-2228
Email: info@ecengmfg.com
back
to top
|
