| EC-7
Trim Shear Features
- Designed to be hand operated
- Designed in pistol grip and straight
motor configurations
- Does not build up heat on lengthy cuts
- Feed and roll cutters manufactured
from special tool steel,
hardened and ground for long life
|
Model*
|
Mild Steel Capacity (Gauge)
|
Feed At
Ft./Min.
|
Throat Capacity (Inches)
|
Weight (Lbs.)
|
Length (Inches)
|
Height (Inches)
|
Width (Inches)
|
Minimum Hose Size (Inches)
|
Order Feed
|
Cutters Roll
|
|
EC-7 LR
|
13
|
8 Apx.
|
1 1/4
|
4 1/2
|
10 1/4
|
3 13/16
|
3 1/4
|
5/16
|
EC 9097
|
EC 9098
|
|
EC-7 PR
|
13
|
8 Apx.
|
1 1/4
|
5
|
8 1/4
|
3 13/16
|
3 1/4
|
5/16
|
EC 9097
|
EC 9098
|
|
|
|
|
|
|
|
|
|
|
|
|
| * L = Straight Motor P
= Pistol Grip Motor R =
Reversible Motor |
|
|
|
back to top
EC-7 Product Illustration
click to enlarge
back to top
EC-7
Trim Shear Parts List
| Index |
Part
# |
Previous
Part # |
Description |
Quantity |
| 1 |
EC 9082 |
|
Worm Wheel R.H. |
1 |
| 2 |
EC 3791 |
843791 |
Retainer Ring |
1 |
| 3 |
EC 9099 |
|
Feed Shaft |
1 |
| 4 |
EC 9072 |
847441 |
Needle Bearing |
2 |
| 5 |
EC 5854 |
845854 |
Worm Wheel Key |
2 |
| 6 |
EC 3791 |
843791 |
Retainer Ring |
1 |
| 7 |
EC 2086 |
842086 |
Spur Gear Key |
2 |
| 8 |
EC 9065 |
|
Rear Cover |
1 |
| 9 |
EC 9059 |
|
Spur Gear |
2 |
| 10 |
EC 9067 |
|
Housing |
1 |
| 11 |
EC 9100 |
|
Cutter Shaft |
1 |
| 12 |
EC 9063 |
|
Shaft Bushing Rear |
1 |
| 13 |
EC 9313 |
|
Cover Spacer 0.002 inch |
* |
| 13 |
EC 9314 |
|
Cover Spacer 0.003 inch |
* |
| 13 |
EC 9315 |
|
Cover Spacer 0.005 inch |
* |
| 14 |
EC 9066 |
|
Front Cover |
1 |
| 15 |
EC 9083 |
|
Shaft Bushing Front |
1 |
| 16 |
EC 9064 |
|
Cutter Key |
2 |
| 17 |
EC 9070 |
|
Lock Screw |
2 |
| 18 |
EC 9097 |
|
Feed Cutter |
1 |
| 19 |
EC 9098 |
|
Roll Cutter |
1 |
| 20 |
EC 9054 |
|
Bearing |
1 |
| 21 |
EC 3692 |
|
Drive Shaft ** |
1 |
| 22 |
EC 9057 |
|
Worm Gear Pin |
1 |
| 23 |
EC 9056 |
|
Worm Gear R.H. |
1 |
| 24 |
EC 9004 |
|
Drive Shaft Nut |
1 |
| 25 |
EC 9053 |
|
Bearing |
1 |
| 26 |
EC 9077 |
|
Bearing Retainer |
1 |
| 27 |
EC 3312 |
843353 |
Grease Fitting |
1 |
| # |
EC 9074 |
|
Adaptor |
1 |
|
# Not Shown on Drawing
* Number of Spacers required is variable
** Available in Dog Drive as a replacement part only
– Order EC 9080
back to top
EC-7 Trim Shear Service
& Maintenance Instructions
Operation:
The tool is designed to operate
on 90 PSI air pressure using a 3/8 inch hose up
to 8 feet in length. If additional hose is required,
a 1/2 inch or larger hose should be connected
to the 3/8 inch hose.
Lubrication:
An automatic in-line filter lubricator
is highly recommended to increase tool life as
well as keeping the tool in sustained operation.
If in-line lubricator is not used, the tool should
be lubricated several times daily by disconnecting
the air hose and injecting a few drops of a high
grade No. 10W machine oil in the air inlet. |
back to top
Product
Safety Warnings
For Your Safety make
sure you apply standard shop
practices at all times when
using this tool. Your failure to apply
these practices may result in serious bodily injury.
Protect your eyes, ears,
and other parts of your body by using safety equipment;
to include Respirator, Safety Goggles, Ear Mufflers
and other necessary safety devices at all times when
operating this tool or when you are in the area where
this tool is being operated.
For maximum stability and safety,
operate this tool only with both hands on the tool.
Follow the cutting tool manufacturer’s mounting
and operating instructions and avoid any direct contact
with the sharp cutting edges of the tool.
Modification or improper use
of this tool, including, but not limited
to, removing guards, mufflers, or other safety devices, voids
all responsibilities of the manufacturer.
Excessive air pressure,
over and above 90 PSI, will increase the RPM,
the sound level, and can be a damaging factor to both
the operator and the tool.
Stay alert! Watch what you are
doing! Do not operates this tool when under the influence
of medication, alcohol, or drugs!
Disconnect the air supply before
changing the cutter and whenever making adjustments
or repairs.
Do not remove warning
tags until both sides have been read and understood
by the person(s) responsible for safety in your plant.
If you need any other information, consult
your supervisor or contact:
E-C Eng. & Mfg., Inc.
P.O. Box 1090
Mountain Home, AR 72654-1090
Phone: (870) 425-3979
Fax: (870) 424-2228
Email: info@ecengmfg.com
back to top |
